Clik here to view.
TL084H: Input gets shorted to supply
Part Number: TL084HTool/software:Hi there,I am using TL084H op-amp for low pass filtering a signal and around 1 in each 20 boards has a problem and the problem is that the positive input of U6AA...
View ArticleClik here to view.
PGA308EVM: The detail part# for PGA308EVM
Part Number: PGA308EVMOther Parts Discussed in Thread: PGA308,Tool/software:Hi,We need to ordered the sample of PGA308 and PGA308EVM, and now, we have no idea there are no detail part# in the EVM...
View ArticleClik here to view.
INA333: CJMCU-333 MCU and Impedance to Ground
Part Number: INA333Tool/software:Hi,I'm really a software developer and not good at electronics, so please bear with me.I was recommended the INA333 as a pre-amp for reading EEG, and bought the...
View ArticleClik here to view.
OPA892: Different frequency sinusoidal input signals to the amplifier give...
Part Number: OPA892Tool/software:The circuit schematic is shown below:The physical PCB board is shown below:The two RF connecting wires are used to test only the two-stage amplification constructed...
View ArticleTL081A: TL081ACD
Part Number: TL081ATool/software:Hi Team,Please advise any document show MSL Level will be different based on date code year ?TL081ACDDC : 04++ ( Y2004 ) is MSL 2DC after Y2004 is MSL 1Thank youSai Xian
View ArticleLM2901: LM2901MX/E7000692
Part Number: LM2901Tool/software:HelloWhat does "E7000692" mean in LM2901MX/E7000692?Thanks/Tomas
View ArticleINA226-Q1: My concern is related to INA226 application.
Part Number: INA226-Q1Other Parts Discussed in Thread: INA226Tool/software:Hi TI team,I am designing a 18S BMS Typically for 54V system application . Can i use INA226 for a current monitoring across...
View ArticlePGA309EVM-USB: How to control the Multi Cal using Tio32.dll
Part Number: PGA309EVM-USBOther Parts Discussed in Thread: PGA309Tool/software:Hello,I would like to use the Tio32.dll to control the USB DAQ platform to control the MultiCal hardware. I am using the...
View ArticleClik here to view.
TLV3501: capacitor value error
Part Number: TLV3501Tool/software:I implemented this circuit. But I have a problem. I measure the value of the capacitor with a high-precision LCR meter. And then I insert it into its place in the...
View ArticleLMH32404: Spice Model for TIA Ampli and trasformer balum
Part Number: LMH32404Tool/software:Hi,I'd like to simulate a project using TIA - LMH32404 with a Silicon Photomultiplier from OnSemi Input signal but I'm not able to find Spice Model for 4-CH-TIA...
View ArticleClik here to view.
OPA354: Spice Model for OPA354 simulation
Part Number: OPA354Tool/software:Hi,I am using spice model from TI for simulation of the OPA354 amplifier, I am finding some problems to understand the results:1) using dual power supply +/-5Vdc I will...
View ArticleLM2901-Q1: Worst case Analysis
Part Number: LM2901-Q1Tool/software:Hi,How to perform the worst-case analysis of LM2901-Q1 considering the min to max temperatures (e.g. -10 deg C to 75 deg C)?
View ArticleLMH5401: Where can I find PSRR data for LMH3401/LMH5401?
Part Number: LMH5401Other Parts Discussed in Thread: LMH3401, TPS7A33Tool/software:Hi：Where can I find PSRR data for LMH3401/LMH5401?The circuit has extremely low noise requirements in actual use.I...
View ArticleClik here to view.
THS3470: 10 MHz Square Wave to Sine Wave Conversion on 50 Ω Load
Part Number: THS3470Tool/software:I have a 3.3 V, 10 MHz square wave output from my in-circuit FPGA. I need to convert this signal into a sine wave, isolate it from my digital ground, and transmit it...
View ArticleClik here to view.
AMC3311-Q1: Circuit Design using mentoned component
Part Number: AMC3311-Q1Tool/software:Hi Team,Please find the Attached circuit with two Isolated amplifier.Please confirm the circuit design is proper or not.PYRO_ARM_HIGH_NC & PYRO_ARM_LOW_NC is...
View ArticleClik here to view.
OPA4348-Q1: Voltage Buffer output to ADC has spikes
Part Number: OPA4348-Q1Tool/software:I am using OPA4348AQPWRQ1 as a voltage buffer to a STM32 ADC pin.I need to convert input voltage of +30V to -30V to a 0-3.3V level and hence used a resistor divider...
View ArticleLMH6702: amplification ratio to 1/10(Av)?
Part Number: LMH6702Tool/software:What would be a suitable opamp to use to reduce the amplification ratio to 1/10(Av)?I want change Input(Vp-p: 1.0V) -->Output( Vp-p: 150mV).
View ArticleOPA596: OPA2596
Part Number: OPA596Other Parts Discussed in Thread: OPA2596Tool/software:Hello,Any update on the procution start of the dual version OPA2596?Sergio
View ArticleINA901-SP: Rad hard level "-" vs "L" in 5962-1821001VXC
Part Number: INA901-SPTool/software:Hello, Can you tell me what radiation hardness or testing or level this part has (5962-1821001VXC)? The datasheet shows that the "-" indicates no RHA. But, the TID...
View ArticleINA241A: PWM rejection at 300kHz to 500kHz
Part Number: INA241ATool/software:Hello,We are planning on selecting the INA241A2 with a 5ohm shunt to sense the current on the 3 phases output of our GAN inverter.The current level is 4A mean / 8A...
View Article