Clik here to view.
LM2904: Schematic review
Part Number: LM2904Hi Sirs,Sorry to bother you.Could you help review our schematic as below?Any suggestion are welcome.Thanks!!
View ArticleTHS4513EVM: EVM mechanical drawing
Part Number: THS4513EVMHello-We have a customer who needs a DC-coupled input to our ADS54RF63 ADC. The datasheet for the latter recommends a circuit (Fig. 51) using the THS4509, but the THS4513 might...
View ArticleLMV339: VICR Common-mode input voltage range over full operating temperature
Part Number: LMV339VICR Common-mode input voltage range is only specified at 25°CWhat is the performance for VICR Common-mode input over full operating temperature
View ArticleTHS4541: The PSPICE model for ths4541 dose not work
Part Number: THS4541The pspice model does not work for this amplifier, THS4541 - tells me I have unconnected nodes inside amplifier.
View ArticleLM111QML: No supply with signal in input +/-
Part Number: LM111QMLHello team,Good day.i would like to confirm whether there will be an issue if a customer puts an input signal (approximately 4V) when both supplies are at approximately 0V...
View ArticleINA190: SPICE model file (.tsm) on product page missing?
Part Number: INA190On INA190 product page, the newly updated link to the part's TINA-TI SPICE model file is the same as the reference design schematic file (.tsc): www.ti.com/.../toolssoftware I need...
View ArticleTLV7011: Does the TINA model include input capacitance?
Part Number: TLV7011I made a oscillator similar to what is shown in 8.2.3 of the datasheet with a capacitance of 3pF. I then calculated the period of the oscillator by hand and compared it to what the...
View ArticleTI alternative for NJM2382
Hi team,Could you let me know TI alternative for NJM2382?EE: PAC indoor unitCustomer is using NJM2382 ac 1ch as 1ch opamp.Thus i'd like to replace this opamp.Best regards,Kento
View ArticleTHS3201: Alternative device for THS3201
Part Number: THS3201Hello experts,My customer is looking for alternative device for THS3201 becasuse THS3201 is NRND.Do you have recommendation?Thanks and best regards,Ryo Akashi
View ArticleClik here to view.
CCS/INA226: INA226 how to read 03h, 04h, 05h address
Part Number: INA226Tool/software: Code Composer StudioDear,our client use INA226, and we can read 00h,01h and 02h, but we cannot to read 03h, 04h and 05h, GUI show "00"how to read address 03h, 04h and...
View ArticleClik here to view.
LM258: LM258DR MARKING
Part Number: LM258Sir, please advise marking reading for LM258DR, thank you.
View ArticleTLV369: OPA LOW Iq and BW 10K
Part Number: TLV369Could TI recommend a Low Iq OPA which gain BW is >=10K? Thank you.
View ArticlePGA281: Below 10nA current measurement range?
Part Number: PGA281With the PGA281 is it possible to measure 10uA to 100mA with a voltage of ±15V.We use it as a High-Side current measurement solution.My question is:1. Is it possible to measure 10nA...
View ArticleClik here to view.
INA111: ina111
Part Number: INA111Hi,we are designing a new electronic card on the previous electronic card design we used the INA111AP now we want to use the INA111AU (surface-mount package).in the datasheet...
View ArticleTLV522: Can TLV8802 be replaced by TLV522?
Part Number: TLV522Greetings,We've have used TLV8802 for a PIR sensor signal amplification circuitry, similar to the one in the TLV8802 datasheet's first page. Would TLV522, which is pin and package...
View ArticleLM139A: Output surge current rating for capacitive load.
Part Number: LM139AWe currently have this comparator in one of our designs. The output is connected to a 6.8nF capacitor through 10 ohm resistor and the assumption is that, with 12V supply the output...
View ArticleOPA2317: 5V input while device is powered off
Part Number: OPA2317Hello,Is it safe to have a 5V voltage at the input of the device when the device is not powered? Will there be no issues or permanent damage if this happens?Thank you!
View ArticleBOOSTXL-3PHGANINV: Power of the inverter
Part Number: BOOSTXL-3PHGANINVWhich is the power that the inverter can provide to me? It is based on the input voltage and the nominal current? 48 V and 7 A rms?
View ArticlePGA281: Absolute maximum short term input terminal input current
Part Number: PGA281Hello,I see on DS page 2 that short term fault current into the "terminals" must be limited to +/- 10 mA with external current limiting to prevent permanent damage to the part. With...
View ArticleXTR300: Imon Disconnected
Part Number: XTR300When operating the XTR300 in open loop mode, we notice that Icopy does not output to Imon. Please advise how to internally connect Imon to the current mirror in open loop mode.
View Article