Quantcast
Channel: Amplifiers forum - Recent Threads
Browsing all 19118 articles
Browse latest View live

Current Sensing Amplifier Solution

Hi Team,We are looking for Current sense amplifier for our RF Module Test Jig to measure the sleep current and uplink current[Peak]. Kindly suggest me the suitable workaround solution to build the...

View Article


TINA/Spice/OPA857: OPA857

Part Number:OPA857Tool/software:TINA-TI or Spice Modelshi,i have generated a Gaussian pulse with pulse width of 10ns in matlab and generated a .WAV file.after generating the .WAV file and while giving...

View Article


INA200: The Max output current of the CMP_OUT pin

Part Number:INA200Hi expert,Could you tell what's the maximum output of the CMP_OUT when this pin output high voltage? Thanks.

View Article

INA210-214

Hi Sirs,Sorry to bother you.I think it would be good if the Digital output can only provide HIGH/LOW signal instead of I2C.Therefore, I found INA210~214 which may feet our application.Our application...

View Article

VCA810: Amplitude control of sinusoidal signal

Part Number:VCA810Dear all,I need to control the amplitude of a sinusoidal signal with frequency between 0 and 1 kHz and amplitude 1V. I am guessing to use the VCA810 with a voltage analog input  0 -...

View Article


OPA140: OPA140

Part Number:OPA140For a critical project, we need to know something about the long term Vos drift for this chip. IT there anything available?

View Article

USB2ANY: Device Manager doesn't show USB2ANY

Part Number:USB2ANYI connected my laptop to USB2ANY to evaluate the low power DCDC device which is controlled by I2c.But the GUI software shows that ‘Hardware not Connected. Failed to connect’.So I...

View Article

Image may be NSFW.
Clik here to view.

OPA2673: Independent amps

Part Number:OPA2673To whom it may concern,I wonder if the two 1/2 amplifiers in OPA2673 are designed only to operate in a differential fashion, or can I just use 1 of the 2 amplifiers, with the other...

View Article


TLV2171: Input offset voltage drift maximum value?

Part Number:TLV2171Hi,we've only specified the typical value of Input offset voltage drift, but what's the maximum value?

View Article


INA230: BUS pin input impedance

Part Number:INA230Dear, support Team.It has a nominal value of 830 kΩ, but what is the maximum and minimum impedance over the full temperature range?I’m calculating the error with the source...

View Article

Image may be NSFW.
Clik here to view.

TL084: TL084 zero-input and low temperature/ high humidity issues

Part Number:TL084Hi Team,My air conditioner customer has some problems about the TL084 current acquisition circuit. (Circuit below and attached tina files)The +/- 8V (maximum range) sin signal @60Hz...

View Article

LM111QML: Mil-Std-883 Method 5004 Tests for Military Lot Screening

Part Number:LM111QMLI have a question about LM111H/883.Is LM111H/883  applicated Mil-Std-883 Method 5004 Tests for Military Lot Screening ?www.ti.com/.../samplebuy

View Article

LM358-N: Maximum output possible for dual supply at 3.3 V

Part Number:LM358-NHi all, I'm new to the electronics world and op amps have me a bit turned around regarding how to figure out if I'm in dual supply mode and Vcc is 3.3 V, what realistically is that...

View Article


Selecting a Sine Wave Generator

Hi Ti,I am looking for a small footprint, quick-to-implement sinewave generator that meets the following condtions:1. I have a 5V and +-12V power supply on my circuit, so the sinewave generator needs...

View Article

Image may be NSFW.
Clik here to view.

TL331-EP: Startup behavior question

Part Number:TL331-EPI have a customer using the TLV331-EP in the following config:As you can see below, output is low when non-inverting input exceeds the value on inverting input at startup.Any...

View Article


OPA4727: Phase Reversal?

Part Number:OPA4727I'm seeing what looks like phase reversal in OPA4727. Has this been seen before. VCC is around 9V.I like the voltage specs of the op amp and the trim, but I don't need the speed. It...

View Article

OPA211: Build a high precision voltage controlled current source using a...

Part Number:OPA211Dear TI team, We want to build a high precision VCVS using a combination of a difference amplifier and a high precision op-amp. The frequency range is 1KHz to 1MHz and the current is...

View Article


Image may be NSFW.
Clik here to view.

TINA/Spice/TIDM-1000: The development board purchased was damaged.

Part Number:TIDM-1000Tool/software:TINA-TI or Spice ModelsHI.Our company purchased TIDM-1000 development board in MOUSER. After receiving the goods, we found that it was damaged. How to deal with it?

View Article

Image may be NSFW.
Clik here to view.

INA1620EVM: Using external resistors to set the amplifier gain in INA1620EVM...

Part Number:INA1620EVM1. R15=R20 is Not matched...2. If we connect the IN- to GND,and Set R1=R7=1K ohm,R2=R6=2Kohm:when using Equation (4), ,VRightChannelOutput = (1k/(2k+1k))*(1+2k/1k) * IN+ = 1*...

View Article

TINA/Spice/OPA855: PSPICE MODEL FOR OPA855

Part Number:OPA855Tool/software:TINA-TI or Spice ModelsHi,is there a pspice model for OPA855 ?thanksOhad

View Article
Browsing all 19118 articles
Browse latest View live


<script src="https://jsc.adskeeper.com/r/s/rssing.com.1596347.js" async> </script>