OPA188: The amount of characteristic change due to aging
Part Number:OPA188One of my customers wants the following data strongly.Please tell me about the following devices.・OPA188AIDBVTCould you please tell the amount of characteristic change due to aging if...
View ArticleClik here to view.
LMV324: About output voltage.
Part Number:LMV324Hi team.I'd like to give me your advice about output voltage for voltage follower.Our schematic is bellow.Its a just simple voltage follower.The output result is around 2.7V when it...
View ArticleLM339: LM339 or TL074(Selection)
Part Number:LM339Hi,I have an application(Solar inverter) where I have to sense AC/DC voltages, current and generate reference voltages (1.65V and 2.5V). I was confused between LM339 and LM074 quad...
View ArticleINA168: Always positive bias current (into the device)?
Part Number:INA168Hello,is the bias current of the INA168 always sinked into the device (in datasheet as positive), or is it possible that e.g. at low VCM also a current is sources by the IC?
View ArticleOPA857: 20V/V amplification
Part Number:OPA857I am looking for a suitable low noise, low distortion 20 V/V post amplifier for OPA857 TIA. In my application, the bandwidth is around 100 MHz. The TIDA-00725 reference design uses...
View ArticleINA170: INA170 Ground Referenced Load, bidirectional current measurement
Part Number:INA170TI,I'm currently exploring use of the INA170 to measure the bidirectional current on the output of an Improved Howland Current Pump circuit that has a ground referenced load.As you...
View ArticleTIDA-060002E1 Reference design
Hello, I would like to know if the reference design TIDA-060002 will be eventually available as a demonstration board. We would like to test this design for applications using a laser seed diode with a...
View ArticleINA240: A question about INA240 output capacitive load
Part Number:INA240Hello,We are using INA240A2 to measure motor current. However, per the datasheet, the INA240A2 output maximum capacitive load should be limited to 1nF. So, we added a buffer in...
View ArticleONET8501PB: ONET8501PB input threshold adjustment range
Part Number:ONET8501PBHi,ONET8501PB and ONET1151P are offering some input threshold adjustments. But it is in digital form from 1 to 255 and there is no specification what exact range is covered with...
View ArticleTINA/Spice/TLV2462: TLV2462
Part Number:TLV2462Tool/software:TINA-TI or Spice ModelsHello ,If i try to simulate this operational amplifier i am getting the error as subcircuit is not there. So I need the model file for this opamp...
View ArticleLM13700: What is function difference between LM13600 and LM13700.
Part Number:LM13700 Hello guys, One of our customers is looking for TI device which can NJM13600 with because the competitor device will be EOL soon. NJM 13600/13700...
View ArticleClik here to view.
LM2907-N: Max Output Voltage isn't Outputted at Max Frequency
Part Number:LM2907-NHi TI forum, so I'm designing a circuit to take rpm and convert it into a voltage to be read by an Arduino. I have create a circuit using the lm2907 IC but when I use an input...
View ArticleLMH6881: DC common voltage input
Part Number:LMH6881Hello,I cannot found specification for dc common voltage input range. I use LMH6881 as single ended amplifier, one input for signal 500 mVpp and second for dc compensation (DAC...
View ArticleOPA691: opa691
Part Number:OPA691hi am naveen am design a bandpass filter using opa691 in that i want single supply only can you share the single supply design file with filter circut
View ArticleClik here to view.
THS4130: Power Down and Power up speed
Part Number:THS4130Hi,how fast does the THS4130 goes to power down and how fast can it go to power on?I am using the LT1206 as a pulser with +15V and -15V supply.By pulser i mean disabling and enabling...
View ArticleLM124AQML-SP: 5962R9950402VDA
Part Number:LM124AQML-SPHi.How much reverse current does each of the 4 inputs and 4 outputs support when the Vcc is 0?Depending on the configuration we have implemented, there may be a case in which...
View ArticleClik here to view.
PGA281: Operation of PGA281 for Min Input voltage supply
Part Number:PGA281Hi ,I am using PGA281 with input stage supply of 10 volts Nominal (VSP=10 V and VSN=0V). But in my system, the supply voltage may vary upto 9.5 Volts ( 10 +/- 5% worst case).In the...
View ArticleBest Easy To Use and Integrate Op Amp for an Electret Microphone
Hey, I am designing a portable recorder with a Raspberry Pi and I am trying to select the best op amp for my project, can anyone recommend one or more that reach my criteria:Adjustable gain (either...
View ArticleClik here to view.
INA302: AC current sensing
Part Number:INA302HI TI,I need over current protection for AC.Please refer to below block.My concept is disconnect from ac line when the current flow above the threshold i set. (2A)You can also suggest...
View ArticleWEBENCH® Tools/FILTERPRO: Filter Design based on fully differential amplifier
Part Number:FILTERPROTool/software: WEBENCH® Design ToolsHi team,I'd like to design filter based on fully differential amplifier.But I can't find how to do it on...
View Article