AMC1200: reliability data
Part Number:AMC1200Hello every oneI'm looking for the FIT rate of AMC1200BDUB.I didn't found it on TI site, some one can help me?thank you
View ArticleTINA/Spice/TLV8542: Spice Model Misleading and Wrong
Part Number:TLV8542Tool/software:TINA-TI or Spice ModelsHello Precision Amplifiers Forum,This may belong in the Simulations and Models Forum, but I believe this forum will best answer my immediate...
View ArticleOPA330: Input Impedance
Part Number:OPA330I am having a little difficulty understanding the impedance specifications. The data sheet for the OPA330 does not list any impedance values. I did read a post in E2E that explained...
View ArticleLMP7731: Input capacitance
Part Number:LMP7731Where I can get the value of input capacitance for this OpAmp?I want compare it with ADA4528-1 and this characteristic is important in an application.
View ArticleClik here to view.
LMP7721: Gamma radiation sensor
Part Number:LMP7721Hello,I have inherited this radiation detection board design at work. None of the original designers are with us and very little documentation exists. The design has been through...
View ArticleLMH6401: input common-mode voltage
Part Number:LMH6401Urgently need clarification of the following Electrical Characteristics, Vicm, Viclr, Vichr, found in the datasheet; literal interpretation implies there is dc common mode voltage...
View ArticleClik here to view.
AMC1200: AMC1200BDWV
Part Number:AMC1200Dear,I have a question about AMC1200BDWV datasheet description.3.3V Operation on Low-side Does it mean it only can be used on low side? We want to replace ACPL-C790-500E with...
View ArticleTLE2061M: Thermal Impedance data
Part Number:TLE2061MHi,Can you please provide the following thermal impedance data for TLE2061MD?1. Junction to lead (pin 4 and pin 7)2. Junction to Case (plastic body)Thanks,Shihab.
View ArticleOPA192: Long term effect of output saturation
Part Number:OPA192Is there any long term harm to driving the OPA192 or OPA4192 so that the output drives to the negative rail? I see from the data sheet that there is a recovery time associated with...
View ArticleClik here to view.
LM2907-N: NPN flow sensor circuit for LM2907-N
Part Number:LM2907-NHello,I want to convert the frequency signal from this flow sensor:to a voltage from 0-10VThe input voltage is 12V DCThe max frequency is 80Hz the normal operating frequenc is...
View ArticleOPA128: Top and Side Markings Required
Part Number:OPA128Hello TI,I need the Top and Side Markings for the OPA128SM.Can you send us a reference picture or diagrams of the CAN package top and side markings? We are finding different markings...
View ArticleLF398-N: What is advantage of using two of these sample-hold circuits in tandem?
Part Number:LF398-NHello,On page 20 of the datasheet for this part shows an example of typical applications, titled "Fast Acquisition, Low Droop Sample and Hold". The datasheet I'm looking at...
View ArticleClik here to view.
LMP91200: amplifier for differential pH sensor
Part Number:LMP91200I am aware of the LMP91200. However, we need to use a fully differential pH probe - see attached diagram - which has the contained liquid as its ground reference. Could you suggest...
View ArticlePGA280: Schottky diode spec
Part Number:PGA280Hi,I would like you to cofirm about below.* Which schottky diode should be selected ?According to datasheet of PGA280, there is following description.VSN is connected to the...
View ArticleClik here to view.
LMP91200: ORP SENSING USING LMP91200 IC
Part Number:LMP91200Hello SirI am using LMP91200 IC for pH as well as ORP sensing.For pH sensing range is -500 mV to +500 mV, it works fine.But for ORP sensing Range is -2000mV to +2000mV,Can I...
View ArticleXTR115: XTR115
Part Number:XTR115Hi,I have XTR115 but I don't have instrumentation amplifier.I want to check 4-20mA current at the output of XTR115.So it is possible to check by applying 40-200uA at IN pin with...
View ArticleXTR115: XTR115
Part Number:XTR115Hi,I have XTR115 but I don't have Instrumentation amplifier. I want to check 4-20mA current at output of XTR115.So it is ossible to check by applying sufficient current at IN pin with...
View ArticleClik here to view.
PGA308: Why PGA308 OTP registers automatically become garbled?
Part Number:PGA308Hi team,Our customer from deyi support is using our PGA308 in their sensor system. Schematic is as follows:They made 30 several sensors, there have been four sensors of them has the...
View ArticleXTR115: Loop Current Changes with Loop voltage
Part Number:XTR115Hello,I am using XTR115 in my application and the circuit works fine (except some non linearity) with 4 to 20mA output. when I changed Vloop from 16V to 24V, the DC loop current...
View ArticleLMP91000: Automotive CO2 sensor application.
Part Number:LMP91000Dear team,My customer want to know about Automotive CO2 sensor application. 1. Is there any AFE solution of Automotive CO2 sensor application? I have been finding AFE of CO2 sensor...
View Article