TLV274: TLV274
Part Number:TLV274Hi E2E experts ,Could you please check for us if with a Single supply of 4.7V and GND the TLV274can sink negative current from a current source connected to its outpur ?Best regards...
View ArticleClik here to view.
Video Operational Amplifier
Dear Team,I am looking for a Video operational amplifier like TSH62.Please refer to the below link. Do we have a similar solution like this? Thank you.
View Articlexreference for LT1028
Hi, I am looking for a cross reference for LT1028. The use case is for active filter in a PLL. thank you in advance. regards, Simon.
View ArticleClik here to view.
MPY634: Divider application - how to disable multiplying by 10V
Part Number:MPY634Hello,At the beginning I would like to highlight that I am at my beggining of the journey with electronic circuits, so my apologies for very basic and maybe not clear explanations.I...
View ArticleLM7322: Supply configuration for LM7322
Part Number:LM7322Hi,May I understand if LM7322 is able to take 0 to 30V for both supply voltages and signal?Is the positive max clamp at +15V?Thanks,Christina
View ArticleINA118 DC amplification
Hello,I'd like to do a DC amplification thanks to INA118, from (O/1 V to 0/10 V ) is it possible or it's just an AC amplifier ?? because i didn't achieve to do itThank you !
View ArticleClik here to view.
OPA2316-Q1: OPA2316 is damaged easily
Part Number:OPA2316-Q1Dear,I am using the buffer and filter schematic as below for ADC input of F28379D Launchpad. The input signal is differential signal which is the output of AMC1200 with Vcm =...
View ArticleLMP91000EVM: is taking a long time to stabilize
Part Number:LMP91000EVMPart number : LMP91000Hardware : LMP91000EVM from Texas Instruments, with : 2-wire jumper installed ( short circuited ) Q1 and R12 not populated C2 and R3 not populated JMENB...
View ArticleISO124: ISO124 about the output voltage question and the supply voltage question
Part Number:ISO124Hi team,The customer would like to use ISO124. Q1: If VS1 is +/-15V and VS2 is +/-5V, can ISO124 work fine? Should the VS1 voltage the VS2 voltage be the same?Q2: If VS1 is +/-15V...
View ArticleClik here to view.
TINA/Spice/OPA333: Can someone please explain to me why i can't get this...
Part Number:OPA333Tool/software:TINA-TI or Spice ModelsThis exact schematic is shown in the OPA333 datasheet, with a formula Vo = (1+2R2/R1)*(V2-V1). Yet i can't get it to work.This general concept...
View ArticleClik here to view.
INA326: EMG Amplifier causes supply voltage to drop form 3.3 V to 2.7 V
Part Number:INA326Hi All,I designed EMG amplifier around INA326 instrumentational amplifier. It is soldered on a dual layer PCB board with huge ground plane. When powered up without INA circuit draws...
View ArticleTLV521: offset voltage vs output current over 2mA
Part Number:TLV521Hello,Our customer want to know the input offset voltage data with higher output current, for example, 10mA and 20mA,however, in the datasheet p7 figure 8 and 9, that is only...
View ArticleTLE2022A-Q1: KSVR at 30KHz
Part Number:TLE2022A-Q1HiRegarding to TLE2022A-Q1, we want to make sure it if KSVR around 30KHz is characterized over 35 dB.(KSVR at 30KHz (min) = 35dB)Could you please tell me your view?BestRegards
View Articleopa2187: OPA187
Part Number:opa2187Can you give me the scoop on your OPA187? I have the data sheet but don't seem to see anyone selling them. I do see the OPA2187 that is also on the same data sheet. Is it too new or...
View ArticleClik here to view.
OPA1652: Replacing OPA2134 with OPA1652
Part Number:OPA1652Hi,Could you please give us your advice whether we can replace OPA2134 with OPA1652 in the following schematic or not ?Best regards,Kato
View ArticleClik here to view.
INA826: Long Term Gain Drift
Part Number:INA826Hi all,I'm considering a INA826 for a high output impedance current source. I don't care much about the exact current but about the stability.The current must not change for different...
View ArticleXTR300: Do TI have solution to get the +-40mA output solution/IC for PLC/DCS...
Part Number:XTR300DearsMy customer is using XTR300 for +-20mA analog ouput solution, but there is a new requirement for increasing the output current range to +-40mA.I would like to check with product...
View ArticleOPA356: Back-termination
Part Number:OPA356In the Application Information Section of the datasheet for the OPA356 it states :"The OPAx356 output stage is capable of driving a standard back-terminated 75Ω video cable. By...
View ArticleClik here to view.
ISO124: Differential Inputs, such as reduced line AC signal, are they possible
Part Number:ISO124Working on a design project to measure AC and DC signals into a custom data acquisition system. We've tested the ISO124 with AC and DC common industrial voltages and all seems to...
View ArticleCCS/OPA140: Can OPA140 drive 50ohm load as unity gain buffer (low noise, low...
Part Number:OPA140Tool/software: Code Composer StudioDear Support,I am considering OPA140 as a Unity gain buffer to interface a 50 Ohm spectrum analyzer with a high-Z source.Frequency range of interest...
View Article